OP126
10mm Super Bright Green LED with water clear lens. 30,000mcd 3.2Vf@20mA, Ifmax continuous=25mA, 30deg viewing angle. Ifpeak 100mA 0.1ms pulses, 1/10...
£0.29
Add:
OP132
Green/Yelow LED backlight. Alphanumeric dot matrix. 80 characters over 4 lines. Display area 76x26mm. Display bezel 98x40mm. 5V supply voltage....
£6.16
Add:
OP133
Reliably space and support your LED above the PCB - for 5mm leds. 5mm diameter, 13mm long.
£0.11
Add:
OP134
White OLED display panel 128x64 pixel resolution. 4-Pin I2C & power connection. Arduino compatible using the Adafruit SSD1306 and GFX libraries -...
£4.16
Add:
OP135
Water clear lens, standard brightness. 35mcd 2.0Vf lfmax=20mA
£0.13
Add:
OP136
Water clear lens budget led with a very high brightness. 2.0Vf lfmax=30mA. Lead length 18mm max.
£0.12
Add:
OP138
Mounted on 20mm diameter star heatsink. Colour - Cold white 5000K - 5650K. Vf=2.85V-3.85V (3.3V typical). 350mA forward current. 120-155lm 130deg...
£1.56
Add:
OP139
Mounted on 20mm diameter star heatsink. Colour - Cold white 5000K - 5650K. Vf=3.1V-4.1V (3.6V typical). 750mA forward current. 218.9-284.5lm 130deg...
£1.92
Add:
OP143
1.8 inch TFT display using the ST7735 chip with 128x160 colour pixels. Rear mounted SD card slot allows bmp images stored on the card to be shown on...
£4.78
Add:
OP144
Kingbright L-7113LID 5mm Red LED. 5mcd brightness maintained down to 2mA forward current. Vf = 1.7V (2.5V max). If = 30mA max.
£0.14
Add:
OP145
Kingbright L-7113LGD 5mm Green LED. 3.2mcd brightness maintained down to 2mA forward current. Vf = 1.9V (2.2V max). If = 25mA max.
£0.14
Add:
OP146
Kingbright L-7113LYD 5mm Red LED. 3.2mcd brightness maintained down to 2mA forward current. Vf = 1.8V (2.1V max). If = 30mA max.
£0.13
Add:
OP148
Kingbright L-7104LID 3mm Red LED. 3mcd brightness maintained down to 2mA forward current. Vf = 1.7V (2.5V max). If = 30mA max.
£0.15
Add:
OP149
Kingbright L-7104LGD 3mm green LED. 2mcd brightness maintained down to 2mA forward current. Vf = 1.9V (2.5V max). If = 25mA max.
£0.17
Add:
OP150
Kingbright L-7104LYD 3mm yellow LED. 2mcd brightness maintained down to 2mA forward current. Vf = 1.85V (2.5V max). If = 30mA max.
£0.13
Add:
OP155
Strip of 8 x RGB WS2812B addressable LEDs. Supply - 5Vdc. Power - 2.4W (480mA maximum drain per strip). Length 130mm, width 10mm. Black, adhesive...
£1.00
Add:
OP158
Low intensity colour diffused violet 5mm LED. Frequency 405nm. 68mcd brightness at 20mA If. Vf=3.4V lfmax=30mA
£0.60
Add:
OP159
30deg viewing angle, 3.1Vf, If=30mA max.
£0.32
Add:
OP163
3mm Kingbright L-34GD LED 32mcd 2.2Vf lfmax=25mA. Lead length 28mm max.
£0.18
Add:
OP171
High efficiency 5mm standard brightness LED. 80mcd 2Vf lfmax=30mA. Lead length 28mm max.
£0.13
Add:
OP172
Green 5mm standard brightness LED. 45mcd 2.2Vf lfmax=30mA. Lead length 28mm max.
£0.17
Add:
OP173
High efficiency 5mm standard brightness LED. 40mcd 2Vf lfmax=30mA. Lead length 28mm max.
£0.12
Add:
OP174
Amber 5mm standard brightness LED. 30mcd 2Vf lfmax=30mA. Lead length 28mm max.
£0.16
Add:
OP178
10 Segment bargraph. 10 leds in a single package with individually accessible anodes and cathodes. Standard 0.1" pin pitch. Vf=3.1 to 3.6V....
£1.09
Add:
OP180
10 Segment bargraph - 5xGreen, 3xYellow, 2xRed leds in a single package with individually accessible anodes and cathodes. Standard 0.1" pin pitch....
£1.12
Add:
PCB010
A PCB for creation of a customised, barebones, Arduino-compatible control module. This board, now in version 2.0, dispenses with the USB interface...
£1.44
Add:
PCB016
Simplify effects pedal off-board wiring. Mount your true-bypass 3PDT foot switch, LED and current limiting resistor (CLR) and wire the main board,...
£0.99
Add:
PCB017
Simplify effects pedal off-board wiring. Wire input and output jacks and main board direct to a central switching PCB carrying the true by-pass 3PDT...
£0.84
Add:
PS11
1.9Vf lfmax=20mA
£1.00
Add:
PS19
2.5Vf lfmax=20mA
£1.00
Add: