M017
Opto-isolated 10A Change-over Relay. On-board optocoupler circuit withrelay active led indicator. 3-way 0.1" pin header strip for 5Vdc supply and...
£2.00
Add:
M014
Electret microphone with comparator circuit for sound detection. Power ON and sound detected LED indicators. Digital and analogue outputs....
£1.22
Add:
M012
Powered by either a 6.5-12V dc supply or from USB, this module plugs into your breadboard and provides a selectable 3.3V or 5V to the power rails....
£1.52
Add:
K141
Micro-Tutor Uno – Arduino/Microcontroller coding and hardware activity board with prototyping area. Welcome to the world of microcontrollers! Our...
£23.28
... more info
K140
Latching tap-responsive switch on mini breadboard - requires no soldering. Ideal for beginners and, of course, the components can be used over again....
£3.91
Add:
K138
Everyone's first project! The Flashing LED Project on mini breadboard - requires no soldering. Ideal for beginners and, of course, the components can...
£2.74
Add:
K136
General hardware pack for FX pedal building. Pack contents: 1 x DC Jack Socket (CN306) 1 x Stereo Input Jack Socket (CN141) 1 x Mono Output Jack...
£12.78
Add:
K128
Create a continuity tester for any lead with up to 8 wires eg Ethernet patch leads, DIN audio leads, USB etc. NOTE: Connectors are not supplied -...
£5.56
Add:
K125
Specifically tuned to the sound of a block-buster 1979 album and emulates the "magic" 70's era fuzz pedal that was somehow clear and articulate on...
£17.15
Add:
K123
"Introduced with a whole series of Ibanez 9-volt pedal (hence the "9" in "TS9") the TS9 featured a larger, easier-to-stomp foot switch than its...
£15.43
Add:
K121
"The PETE CORNISH G-2™ has been hailed as the most original sounding distortion unit available to guitarists in the Rock Arena." - build Pete...
£14.86
... more info Sold Out
K119
"The venerable Clay Jones Overdrive gets the Lovepedal Eternity treatment by Fred Briggs. The ultimate mojo Tubescreamer gets a bit more mojo" A kit...
£18.83
Add:
K118
"One of the most iconic and sought after amps in history ... in a pedal!" A kit of components as recommended by Ivlark for assembly of the Shin's...
£22.69
Add:
K102
Red, amber, green LED traffic light simulator. Should be powered by a PP3 battery - see the battery section. If you require wire - see the cable...
£5.65
Add:
K100
Everyone's first project - flash a LED. Should be powered by a 9V PP3 battery - see the battery section. If you require wire - see the cable section....
£1.88
Add:
K098
Flash a LED to imitate an alarm indicator. Can be powered by a 3 x AA batteries - see the battery section. If you require wire - see the cable...
£3.36
Add:
K092
"Mad Professor Sweet Honey Overdrive (SHOD) is a super touch sensitive medium gain overdrive pedal. It is designed to overdrive distorted amplifiers...
£18.64
Add:
K072
Project constructed on the supplied PCB. Red and green LEDs flash in a rotating pattern with the speed adjustable using a preset pot. Kit contains...
£5.95
Add:
K058
A 100-Piece Transistor Development Kit ideal for the experimenter, hobbyist, technician or student. Contains a selection of the most popular...
£11.63
Add:
K048
Teach Yourself Electronics A kit of components to accompany the Electronics Club website. This excellent site takes you through identification and...
£28.99
Add:
K011
A 613 piece kit containing: 1x 480-Piece Resistor Kit - Containing 30 of each of the following: 10R, 100R, 1k, 10k, 100k, 1M, 22R, 220R, 2k2, 22k,...
£18.94
Add:
HW191
Lens and panel clip for 3mm LEDs. Clear plastic with diffusing rings. Lens diameter 5mm. Overall length 7.3mm. Fit into 4.35mm panel hole and snap in...
£0.47
Add:
HW190
Lens and panel clip for 5mm LEDs. Clear plastic with diffusing rings. Lens diameter7mm. Overall length 11mm. Fit into 6.35mm panel hole and snap in...
£0.39
Add:
HW140
Chrome plated plastic, panel mount bezel for 5mm leds. Requires 8mm mounting hole.
£0.16
Add:
HW139
Chrome plated plastic, panel mount bezel for 3mm leds. Requires 5.7mm mounting hole.
£0.12
Add:
HW138
Metal, panel mount bezel requires 7.7mm mounting hole.
£0.38
Add:
HW132
Metal, panel mount bezel requires 5.7mm mounting hole.
£0.26
Add:
HW125
A budget priced single piece led clip for 3mm leds. Fits an 6mm hole in panels up to 2.5mm thick.
£0.16
Add:
HW124
A budget priced single piece led clip for 5mm leds. Fits an 8mm hole in panels up to 2.8mm thick.
£0.18
Add:
HW094
Plastic clip to mount 10mm LEDs
£0.22
Add:
