QU328
Stereo power amplifier based on the PAM8403 class-D chip. 2.5-5V dc supply and highly efficient class of operation make this ideally suited to...
£0.72
Add:
M101
Stereo power amplifier based on the PAM8403 class-D chip. Module incorporates volume control with on/off switch at fully anti-clockwise rotation....
£1.17
Add:
M050
Card reader/writer interfaces directly with 5V Arduino ports using SPI. 4.5V-5.5V supply. Gnd, Vcc, MISO, MOSI, SCK & CS via 0.1" right angle header...
£1.12
Add:
M095
Stereo power amplifier based on the PAM8610 class-D chip. 7-15V dc supply, input impedance 15k, 4 Ohm - 8 Ohm output impedance. 15W+15W into a 4 Ohm...
£2.36
Add:
M049
I2C comms interface - address 0x48 Supply voltage 2.5V - 6Vdc. Onboard light sensor, thermistor and potentiometer connected to three ADC channels via...
£2.92
Add:
M017
Opto-isolated 10A Change-over Relay. On-board optocoupler circuit withrelay active led indicator. 3-way 0.1" pin header strip for 5Vdc supply and...
£2.00
Add:
M084
Wi-fi and Bluetooth capable development board using the ESP-WROOM-32 chip. 32-bit dual core processor. Up to 240MHz with 512kB RAM. Peripherals...
£8.30
Add:
M064
Double relay module. Inputs Gnd, Vcc (5Vdc), channel 1 signal (active low), channel 2 signal (active low). Channel signals are optically isolated...
£2.52
Add:
M082
DC buck converter module based on the MP2307 IC. Input 4.75V - 23Vdc. Output 1V-17Vdc Output variable by on board miniature preset potentiometer. Our...
£0.84
Add:
M028
Add Wi-fi and web capabilities to your project with this module which is currently in rapid development. The module operates at 3.3V, so level...
£2.06
Add:
M081
4-Channel relay module. Inputs Gnd, Vcc (5Vdc), channel select signal 1-4 (active low). Channel signals are optically isolated from the relay coils....
£3.11
Add:
M065
Input 8V - 36Vdc. Output 1.25V-32Vdc Constant max. output current can be varied up to 5A. 75W max. NOTE: To ensure correct current regulation and...
£2.62
Add:
M038
Based around the ESP8266 ESP-12 and NodeMCU firmware this module provides an integrated Arduino-like hardware platform for developing wifi IoT...
£5.64
Add:
M059
Input 3V - 40Vdc. Output 1.3V-35Vdc Rated output current 2A max continuous, 3A with additional heatsinking. Buck converter operating at 150kHz - max...
£1.22
Add:
M044
Input 0.9V - 5Vdc. Output 5Vdc @ 650mA max. via USB type A socket. Ideally suited to charger projects.
£0.74
Add:
M060
Input 2V - 24Vdc. via solder pads or micro-USB socket. Output 28V max. Rated output current 2A max, 1A max continuous recommended, 3.5W approx. Buck...
£1.04
Add:
M104
A high power, variable output, DC-DC boost converter. Input 3V - 30Vdc. (5-30V for optimum operation) via solder pads. Output 35V max. Output voltage...
£2.32
Add:
M105
A high power, variable output, DC-DC boost converter. Input 35Vdc max via solder pads or screw terminals. Output 40V max via solder pads or screw...
£2.93
Add:
M107
A 150W (max) DC-DC boost converter. Input 10-32Vdc max via screw terminals. Output 12-35Vdc @ 6A max. via screw terminals. Output voltage adjusted...
£3.99
Add:
M087
Charger module for 3.7V lithium power (LiPo) packs which do not include their own protection circuit. Feeds a 1A charge current to the battery and...
£1.00
Add:
ST071
Triaxial accelerometer and gyroscope with 6 degrees of freedom. I2C serial interface. 5Vdc supply voltage - Arduino friendly. Applications available...
£2.75
Add:
M088
2-channel H-bridge motor driver board able to drive two independent motors at up to 800mA each. Can also drive a single four line two phase stepper...
£1.29
Add:
M034
PIR motion sensor with high/low TTL 3.3V output signal. Sensitivity (up to 7m) and output duration (20s - 5min approx.) adjustable. 5V - 20V DC...
£1.62
Add:
M033
A low cost, accurate I2C real-time clock. with an integrated 32K AT24C32 EEPROM. Supply voltage 3.3 V to 5.5 V A coin cell battery holder allows...
£3.48
Add:
M069
PIR motion sensor with operating in the 2.7V to 12Vdc supply range. Sensitivity 3-5m with output low to high for 2 secs on detection of motion....
£1.96
Add:
ST096
Doppler effect motion sensor using microwave radar signals. Detection range up to 7m. Can detect motion through many materials. Wide 4-28Vdc supply...
£1.52
Add:
MTR8
Motor voltage range 3-12Vdc (5V-9V recommended). 70-250mA Motor & gearbox dimensions 70 x 22 x 18mm approx. 70-140 rpm approx. Torque 1kgf.cm approx....
£2.46
Add:
M085
Motor driver shield for Arduino - compatible with the Adafruit motor driver library. The board includes two L293D motor drivers and one 74HC595 shift...
£3.45
Add:
M071
Clone of the Arduino Pro Mini with ATMega328P microcontroller operating at 3.3V 8MHz. 100% compatible. The Pro Mini was designed as a low cost...
£3.77
Add:
M055
"Digital Tube" display module - 0.36" This module uses a two pin serial interface to accept display data to the onboard TM1637 IC. Customer Chris...
£1.58
Add: